S-drum: Increases torque at mid- to low-speed and enables quick start. Climbs powerfully. The sound is low, and when the sound is around 90 decibels, the high-speed horsepower will not be sacrificed, and the formation of three wastes will be mainly prolonged to achieve the power improvement effect. (Disadvantage: There is resonance sound at high speeds, and the horsepower at high speeds is not greatly improved). S drums are used for engines with a displacement of less than 2.0.
Internal back pressure: specially designed according to the characteristics of the vehicle itself. Improved mid- and low-speed torque without making any noise. No resonance sound. There is no resonance sound at high speeds and the speed increases quickly. (The sound is similar to that of S drum. Some models cannot be equipped with S drum and can only be equipped with internal back pressure.)
G type: used for large-displacement engines above 2.0. It reduces the sound through three back pressures and extends the airflow pattern. Similar to S drum. The sound is around 90 decibels. Increase torque at medium and low speeds (S drum is used for small-displacement cars below 2.0. G drum is used for large-displacement cars above 2.0)
Direct-displacement: The horsepower at high speeds is increased, but the torque at medium and low speeds is not improved much. More suitable for long-term high-speed running and racing tracks. The sound is around 100 decibels. Quite noisy.
Y type: Improves torque at mid- to low-speed. Noisy. About 95 decibels
Street drum: It increases horsepower and torque, and the sound quality is also very particular. The drum body is completely designed to increase horsepower and reduce volume. It can be selected for walking on the street or at high speed. The entire exhaust section adopts the most popular Japanese gradually amplified design style, 47mm-63mm-76mm. After the 63mm and 76mm are connected with a back pressure pipe, the potential of the engine can be better exerted. The sound is around 90 decibels, which balances the fuel consumption acceleration response and improves the power. The street drum has become an ideal throat for street walking. (The street drum has a good-looking appearance, is painted black, and the car performance is very good.)
M drum: Variable back pressure design, the back pressure is adjusted according to the speed. There is no resonance sound at high speeds. When the engine is at low speed, the gas flow speed is slow, and the speed through the regulating valve will be slower. The smaller the vacuum generated, the smaller the suction force, and the greater the back pressure of the exhaust gas stored per unit time. When the engine is running at a high speed, the gas flows quickly, and the speed through the regulating valve becomes faster, creating a large vacuum, expelling more exhaust gas, and the high-speed exhaust is smooth. It achieves the effect of increasing torque and increasing horsepower at the same time. The high speed (full speed power) is about 85 decibels. It is the most obvious and powerful exhaust pipe in China that shows the most obvious and powerful improvement according to foreign design concepts. The sound comes out at 2500-3000 rpm, and the sound becomes quiet again at 4000 rpm.
HKS type: It is a straight-discharge with back-pressure, which improves the torque at medium and low speeds and the horsepower at high speeds. The sound is smaller than the direct-discharge type, louder than the back-pressure type, relatively crisp, and never disturbing at 95 decibels. There is no resonance sound at high speed. (It has the effect of Japanese HKS) Design principle: the airflow flows along the wall.
Middle section: used to connect the head section and the tail section, and also has the effect of increasing the horsepower by 3-4 horses.
Design issues regarding the angle of motor vehicle exhaust pipes
The exhaust angle of motor vehicle exhaust pipes has always been a difficult problem for professional manufacturers to solve. According to the investigation, the angle direction of the exhaust pipes of cars and light family vehicles is generally backward and parallel to the ground, while the angle of the exhaust pipes of high-power transport vehicles and agricultural vehicles is bent toward the ground. From an environmental protection point of view, there is no new angular discharge design method specified based on the current angular direction design and mechanical design principles of motor vehicle exhaust pipes. The best design solution for the angle direction of all vehicle exhaust emissions should be 180 degrees parallel to the ground and discharge toward the rear of the vehicle. If the design solution is not unified and standardized, each manufacturer's random design of the exhaust pipe exhaust direction will be detrimental to environmental protection and accidental infringement incidents will occur while driving.
1. Unfavorable factors caused by the angle of the exhaust pipe being bent toward the ground at about 45 degrees.
Within this emission angle range, when the car is running, the high-flow exhaust gas will blow up dust on the ground. The faster the driving speed, the greater the degree of dust pollution. At the same time, the greater the power of the car, the greater the flow and velocity of the gas emissions, and the degree of dust pollution will be higher. According to market research, the areas with the most severe dust pollution should be along the highway. The more traffic there is, the more serious the dust will be. On the other hand, dust pollution is also related to the cleanliness of the road surface. The more floating dust on the road surface, the greater the amount of dust blown up by car exhaust.
2. There are also certain problems with the angle of the exhaust pipe being bent toward both sides of the car.
If the angle of the exhaust pipe is bent toward both sides of the car, the exhaust from the car will cause impact damage to pedestrians due to hot airflow while driving. In addition, car exhaust contains unburned atomized oil stains, which include pollutants such as sulfides and carbides, which can cause physical infringement to the human body.
3. When the angle of the exhaust pipe is turned upward, it will cause serious damage to the car body.
This kind of angle is generally not chosen by car manufacturers. Because pollutants such as sulfides and carbides in the exhaust will cause chemical corrosion to metal parts such as automobile bodies, manufacturers generally do not choose this exhaust angle.
According to the relevant provisions of my country's Environmental Protection Law, the machinery industry management departments of various provinces, cities and regions should formulate unified standards for the angle of the exhaust pipes of fuel vehicles, preferably parallel to the ground and discharged rearward. It is also strictly forbidden to implement the design plan where the exhaust pipes are bent to the ground and both sides to reduce the dust pollution generated by motor vehicles when driving and strengthen the operation and management mechanism of environmental protection regulations to make our sky clearer and the environment better.

